logo
Всичко за оръжието и мунициите на едно място

Часовете са според зоната UTC + 2 часа


Дата и час: 28 Мар 2024, 23:55




Напиши нова тема Отговори на тема  [ 2 мнения ] 
Автор Съобщение
Непрочетено мнение Публикувано на: 14 Сеп 2009, 18:01       Заглавие:  Въпрос относно Ruger P95DC
 
Снайперист
Снайперист
Аватар
Offline

Регистриран на: 22 Юли 2009, 16:11
Мнения: 229
Някой знае ли какъв е реда за разглобяване за да се извади иглата на Ruger P95DC ? Не успях да намеря нищо в Интернет. Не ми се напъва с голямата отверка :-)


 
Върнете се в началото
  Профил Започни разговор  
 
  Сподели темата във Facebook
 
Непрочетено мнение Публикувано на: 14 Сеп 2009, 19:12       Заглавие:  
 
Оръжеен гуру
Оръжеен гуру
Аватар
Offline

Регистриран на: 21 Апр 2009, 21:22
Мнения: 8101
Местоположение: USA, FL
Това е за 97 но би трябвало да ти свърши работа:
To do this for a decocking model only (the safety models are different, and I’m not sure how they work), you must first removed the extractor. To do this carefully grasp the extractor hook and pivot it outward 1 or 2mm. While pivoting it outward pull the extractor toward the front of the slide. This will remove the extractor and allow the decocker on the right side of the slide (looking from top of slide) to be removed. Next, you will notice the black leaf spring on the underside of the slide. You must depress this black leaf spring while removing the pin that holds the leaf spring in place. This can be tricky as the black leaf spring is under a lot of tension. Be, careful and take your time and you’ll manage. Once the pin is removed the leaf spring will come out allowing the left side decocker lever to be removed. Now you can push the round firing pin safety located on the underside of the slide and remove the firing pin out the back. Be careful as the firing pin is under spring tension. You don’t want to loose it. Assembly is the reverse of this procedure.


За всеки случай и това:
...in my pistol book they show :using a tool (small screwdriver in side of the slide)flex the extractor outward until it can be levered forward.
Remove the extractor forward and toward the right.
With the safty-levers in off safe postion, use a thumbnail or non-maring tool to nudge the right saftey lever outward. Keep a fingertip below the
lever, to catch the positioning plunger and spring, which will be released downward as it clears the slide.
Turn the left safty lever to a little past on safe position, and remove it toward the left CAUTION: Restrain the firing pin which will be released as the saftey clears the slide.
Remove the firing pin and its spring toward the rear.
Use a non marring tool to drive the rear sight out of its dovetail toward the right. Restrain the firing pin block spring as the sight clears it.
Remove the firing pin block and its spring upward.
Hope this helps....


На страница 26 има схема:
http://pdf.textfiles.com/manuals/FIREARMS/ruger_p95_decocker.pdf


 
Върнете се в началото
  Профил Започни разговор  
 
  Сподели темата във Facebook
 
Покажи мненията от миналия:  Сортирай по  
Напиши нова тема Отговори на тема  [ 2 мнения ] 


Кой е на линия

Потребители разглеждащи този форум: 0 регистрирани и 10 госта



 
Иди на:  

Powered by phpBB © 2020 TheGunMan
This forum is operated and maintened by Stanislav Georgiev - Owner/Administrator, Jordan Cholakov - Adminstrator/Editor and Rossen Hristov - Graphic Designer/Potographer